Home > Return Code > Return Code 0016

Return Code 0016

Contents

S112 - 13 - DCB DOES NOT POINT TO A VALID DEB. ONLY VALID OPTIONS ARE INPUT AND UPDAT. S013 - 7C - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER READER DATASET, BUT THE LRECL PARAMETER IN THE DCB WAS ZERO. S305 - 0C - CSA STORAGE IS NOT IN THE SUBPOOL SPECIFIED. http://jscience.net/return-code/return-code-12-reason-code-49.html

THAT IS, IT WAS FOUND IN AN UNAUTHORIZED LIBRARY. THE RB ADDRESS MUST REMAIN IN THE ECB UNTIL A POST IS ISSUED. S04B - 08 - THE SERVICE ROUTINE'S LAR (IKJTSLAR) WAS INVOKED AT IKJTSLAR, WHICH IS AN INVALID SERVICE ROUTINE ENTRY POINT. THE DCB IS DUMPED TO THE GTF DATA SET.

Jcl Return Code 16

S113 - AN ERROR OCCURRED DURING AN OPEN WITH A TYPE=J OPERAND. IE. INPUT-OUTPUT SECTION.

THE FUNCTION PERFORMED IS TERMINATED. - A AUXILIARY STORAGE MANAGEMENT ROUTINE SUFFERED A TRANSLATION ERROR WHILE USING THE CONTROL REGISTER OF ANOTHER ADDRESS SPACE TO UPDATE THAT ADDRESS SPACE'S LSQA. THIS TYPE OF ERROR OFTEN OCCURS IF A DCB IS SHARED BY TWO OR MORE TASKS, OR IS OPENED AND CLOSED SEVERAL TIMES WITHIN ONE JOB STEP. S046 - SORT CAPACITY EXCEEDED S047 - AN UNAUTHORIZED PROGRAM REQUESTED A RESTRICTED SVC. Cond Parameter In Jcl NOT ENOUGH REAL STORAGE AVAILABLE TO BACK A MINIMUM NUMBER OF VSM CELLS (IN LSQA) DURING LOCAL CELL POOL EXPANSION.

S013 - 48 - AN OPEN MACRO WAS ISSUED FOR A SEQUENTIAL DATASET USING THE QUEUED ACCESS TECHNIQUE, BUT THE BUFFER CONTROL BLOCK ADDRESS WAS ZERO. Jcl Return Code 8 S112 - 02 - DCB NOT IN CALLER'S STORAGE. S213 - 0C - AN I/O ERROR OCCURRED READING A FORMAT-1 DSCB FOR A DIRECT OR INDEXED SEQUENTIAL DATASET, OR THE FORMAT-1 DSCB COULD NOT BE FOUND ON THE VOLUME SPECIFIED S213 - 70 - OPEN DETECTED A CROSS SYSTEM SHARE CONFLICT FOR THE PDSE.

IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S202 OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S202-RC)** S202 - 00 - THE CONTROL PROGRAM FOUND AN INVALID S213 - 68 - AN OPEN FOR A PDSE WAS ISSUED WITH RECFM=FB AND LRECL=0. NOTE: THE MEANINGS OF THE CONTENTS OF GENERAL REGISTERS 11, 12, 13, AND 14 ARE PROVIDED FOR DIAGNOSTIC PURPOSES IN THE FULL DESCRIPTION OF THIS ABEND IN THE SYSTEM CODES MANUAL. S002 - 0C - AN INVALID RECORD WAS ENCOUNTERED ON A PUT OR WRITE OPERATION.

Jcl Return Code 8

IBM software using the following convention regarding program execution: COND CODE 0000 - program successful COND CODE 0004 - warning messages COND CODE 0008 - Serious flaws S003 - 03 - THE ERROR WAS A PRINT SEQUENCE ERROR. Jcl Return Code 16 S0E5 - UNABLE TO DISCONNECT THE VIRTUAL TRACK BUFFER FORM THE VIO DATASET. Return Code 16 In Sort Step In Jcl S16E - 20 - DEB TABLE CONTAINS 32760 BYTES AND TYPE = ADD.

Processing continues.12 (X'0C') An unrecoverable error exists. his comment is here S0E0 - 31 - AN UNSTACKING INTRUCTION WAS ISSUED WHEN THE LINKAGE STACK HAS NO STACK ENTRIES. Processing continues normally with the next set of utility control statements, if any. 12 (X'0C') An error occurred while processing an input or output data set. S013 - 70 - AN OPEN MACRO WAS ISSUED FOR A DATASET ON MAGNETIC TAPE. Ief142i

Some components may not be visible. FORMAT: COND=((value,operator,stepname),(..,..,..)) value - a number from 0 to 4095 operator - GT - Greater than LT - Less than EQ - Equal to NE - Not S104 - 20 - AUTHORIZED PRIVATE REQUEST FAILED - PAGE TABLE PAGED OUT. this contact form S106 - CAN'T FIND IBM SUBTOUTINE.

U0746 - BAD DFP CODE U0779/U0888 - VOLUME FENCED U0999 - BAD DATA U1812 - I/O ERROR WRITING THE TAPE MARK DURING CLOSING OF A MACRO INSTRUCTION. Why bypass a step? S0E3 - THE ERROR OCCURRED WHILE PROCESSING A VIO DATASET.

U3690 - SYSTEM SOFTWARE OR DISK PROBLEM OCCURRED DURING THE EXECUTION OF A LINK OR LOAD INSTRUCTION / INSURE THAT THE LOAD REQUEST IN THE PROBLEM WAS SPECIFIED CORRECTLY AND WAS

S0C7 - DATA EXCEPTION - DECIMAL DATA IS INCORRECT OR IMPROPERLY OVERLAPPED OR NOT VALIDLY INITIALIZED. S0E0 - 30 - A STACKING INTRUCTION WAS ISSUED WHEN THE LINKAGE STACK WAS FULL. Make the current COB2J procedure more readable using temporary datasets and symbolic parameters. The utility ends. 12 (X'0C') The input PDSE could not be opened.

S178 - 20 - AUTHORIZED PRIVATE REQUEST FAILED - PAGE TABLE PAGED OUT. S305 - 18 - PRIVATE AREA SUBPOOL NOT FOUND. S004 - 05 - INVALID FORMAT CARD OR AN INVALID DEVICE SPECIFIED WITH OPTICAL MARK READ (OMR). navigate here S013 - 74 - AN OPEN MACRO WAS ISSUED FOR AN OPTICAL CHARACTER READER DATASET, BUT THE OPEN OPTION DID NOT SPECIFY INPUT.

ENDIF logic is available to control step execution in MVS/ESA VERSION 4 Allows execution of a step or series of steps if the result of a test is true or false. PROGRAM-ID. S0F8 - 04 - THE SVC ISSUER WAS NOT IN TCB MODE. S013 - 14 - AN OPEN MACRO WAS ISSUED WITH OUTPUT OR OUTIN SPECIFIED.

The utility is ended. COND CODE - AN EXEC PARAMETER TO BYPASS STEP EXECUTION Define conditions which, when true, do not execute a step. S306 - 24 - AN AUTHORIZED SERVICE ATTEMPTED TO ACCESS A NON-REENTRANT LOAD MODULE WHICH WAS LOADED FROM AN AUTHORIZED LIBRARY BY AN UNAUTHORIZED CALLER. S002 - RECORD IS GREATER THAN 32,768 BYTES, EXCEEDS MAXIMUM TRACK LENGTH OR STATED BLOCKSIZE, COULD NOT BE CONTAINED IN ONE EXTENT, OR TOO MANY TRACKS SPECIFIED FOR CYLINDER OVERFLOW.

S013 - 3C - A SEQUENTIAL DATASET WAS OPENED FOR INPUT OR OUTPUT, BUT THE BUFFER CONTROL BLOCK ADDRESS WAS 0. IF THE REGISTER 15 RETURN CODE IS AVAILABLE, SUPPLY IT IN THE S213 OPERAND FOR MORE SPECIFIC INFORMATION: H ABEND O(S213-RC) POSSIBLE CAUSE: THE DATA SET IS NOT ON THE SPECIFIED S206 - THE ADDRESS OF THE PARAMETER LIST, OR ONE OF THE PARAMETERS PASSED TO A LINK, LOAD, XCTL, OR DELETE MACRO WAS INVALID.

© 2017 jscience.net