Home > High Cpu > High Cpu Usage Cisco 4500

High Cpu Usage Cisco 4500

Contents

It spiked to 87 percent within the past hour. See the “Monitoring IP Traffic Counts” section. The first function is run the different processes under IOS to carry out the function for a switch operating in a network. The issue of TCNs reduces the aging time to 15 seconds in PVST+ mode. Check This Out

If the interrupt percentage is too high relative to the total CPU utilization percentage, the CPU utilization problem is caused by receiving too many packets from system hardware. To exceed the target CPU utilization by a small amount, or a momentary spike in utilization, is not an indication of a problem that needs investigation. High CPU utilization resulting from low-priority packet processing or background processes is considered normal because the software routinely tries to use all the available time. Use the show platform cpu packet statistics command for all troubleshooting.

K5cpuman Review High Cpu

Issue the show platform cpu packet statistics command in order to check which CPU queue receives the CPU-bound packet. The CPU exhibits high CPU utilization because the Supervisor Engine maximizes the CPU cycles in order to perform all the necessary software packet forwarding and background jobs. Now I must say the name of this process surely means something to someone, but not to me. This is less common than high CPU utilization caused by the receipt of network packets.

Input Acl Punt Packets in input direction that are punted to the CPU due to a lack of additional ACL hardware resources, such as TCAM, for security ACL. A complete or partial SNMP MIB walk. Knowing the time spent at interrupt is critical for determining the cause of CPU utilization. Command To Check Cpu Utilization In Cisco Switch The remaining idle CPU cycles are used for the low-priority processes.

Table 2 provides some basic information about the common platform-specific processes that appear in the output of the show platform health command. L2 Router To Cpu, 7 In other words, if the ACL does not fit into the TCAM, the ACE at the bottom portion of the ACL likely is not programmed in the TCAM. This is useful if the packets are all the same type or originating from the same source. When the Catalyst 4500 runs out of TCAM resources during the programming of a security ACL, a partial application of the ACL occurs via the software path.

Please contact support. Sa Miss Cisco 4500 In order to see which of the platform-specific processes use the CPU under the context of Cat4k Mgmt HiPri and Cat4k Mgmt LoPri , issue the show platform health command. Known symptoms that can occur when the switch CPU is too busy: Spanning-tree topology change—When a Layer 2 network device does not receive timely spanning-tree BPDUs on its root port, it Beginning in privileged EXEC mode, follow these steps to view the system log with the debug messages: Command Purpose Step 1 terminal length 0 Set the number of lines on

L2 Router To Cpu, 7

Step 2 no logging console Disable logging to the console terminal. TagMan-RecreateMtegR 1.00 0.00 10 0 100 500 0 0 0 0:00 K2CpuMan Review 30.00 37.62 30 53 100 500 41 33 1 2:12 K2AccelPacketMan: Tx 10.00 4.95 20 0 100 500 K5cpuman Review High Cpu This situation is often the result of network topology instability. Cisco Iosd Process In this example, the CPU utilization is 64 percent, and the interrupt percentage is 19 percent, which is high.The utilization problem is caused by the CPU processing too many packets received

Join Now For immediate help use Live now! his comment is here UDLD—Detects unidirectional links and prevents forwarding loops. Issue the show processes cpu command in order to check which Cisco IOS process consumes the CPU. Use the show processes cpu command in order to identify the CPU utilization on the Catalyst 4500 switch. Iosd Process 4500

Use to determine how many additional TCAM resources are needed to hold the current network routes. Helpful Information CPU Receive Queues A packet sent to the CPU by switch hardware goes into one of 16 CPU queues, depending on the packet type. Background Information Before you look at the CPU packet-handling architecture and troubleshoot high CPU utilization, you must understand the different ways in which hardware-based forwarding switches and Cisco IOS Software-based routers this contact form ACL with TCP flags other than established IP version 6 (IPv6) routing—This is supported only via the software-switching path.

Use the sdm prefer template-name global configuration command to change to a template that reserves more resources for IP routing. Show Platform Cpu Packet Buffered Configure IP phone ports with a voice VLAN configuration. Some of the packets that are sent for process can be essential for the network operation.

Excessive SNMP polling by a legitimate or misbehaving end station A High Number of Spanning-Tree Port Instances The Catalyst 4500 supports 3000 spanning-tree port instances or active ports in the Per

Investigating further we have narrowed > it > down to the following on the Cisco Bug Report: > > > > High CPU due to Mgmt LoPri process, MAC addresses being Total packet queues 16 Packets Received by Packet Queue Queue Total 5 sec avg 1 min avg 5 min avg 1 hour avg ---------------------- --------------- --------- --------- --------- ---------- Esmp 202760 Edit Account Now Ignore You already have an account in the system. K2cpuman Review show processes cpu sorted [ 5sec ] Shows percentages for CPU utilization and CPU time spent on interrupts and lists the most active system processes in order of CPU utilization.

These include WS-X4014 thru WS-X4516-10GE, Catalyst 4948, and Catalyst 4948-10GE. I started into this by finding the culprit model workstation that was in use. If there is an excessive number of new MAC addresses for the switch to learn, high CPU utilization can result. navigate here Also, review the Configuring Network Security with ACLs configuration guideline in order to optimize the ACL configuration and programming in the hardware.

For information about the CPU SPAN, see the Tool 1: Monitor the CPU Traffic with SPAN—Cisco IOS Software Release 12.1(19)EW and Later section of this document. See the “Analyzing Network Traffic” section for investigation information. Please enter a maximum of {0} characters. {0} remaining of {1} character maximum. Switch# show platform ip unicast counts # of HL3U fibs 2426 # of HL3U adjs 4 # of HL3U mpaths 0 # of HL3U covering-fibs 0 # of HL3U fibs with

However, TCAM is a finite resource. To resolve TCAM utilization issues, you should choose the appropriate SDM template for the switch application. L3 Receive Packets with IP destined to router IP address (such as telnet/ssh sessions to router) Some of the queue names (such as Layer 3 Receive queue) in Table1 are associated HSRP flapping.

In general, you can calculate spanning-tree port instances with this formula: Total number of STP instances = Number of access ports + Sum of all VLANs that are carried in each Caution:Make this age-out change only after careful consideration. In this case, see the “Debugging Active Processes” section.

© 2017 jscience.net